7262 Mi-High Strength Red Thixotropic Anaerobic Thread Locker For Under M20 Thread Locker/ Thread Sealant/ Liquid Gasket

Huitian®7262 is a one-component thread-locking anaerobic adhesive that features thixotropy, medium-high strength, and excellent resistance against fluid. The product cures when confined in the absence of air between close-fitting metal surfaces.Typical ApplicationPermanent locking of thread-locking below M20 can be widely used for locking and sealing parts with large force.Red Screw Thread Locking Adhesive 7262 replacingLoctite262 for under M20 thread lockerProperties before curingTypical value                               RangeAppearance                                    Red liquidChemical type                              MethacrylateViscosity (mPa·s)(GB/T2794-1995)Brookfield RVT3#spindle 2.5rpm                           5,000~8,500 thixotropy20 rpm                                           1,800~2,400 thixotropyDensity (g/cm3)                                    1.10                                   1.00-1.15(GB/T13354-1992)Flash point (℃)                                                                                 ＞93(SH/T0733-2004)Max filling gaps (mm)                           0.13Fixture time (min)                                                                               ≤20Properties after curingCuring time at RT (h)                              24Breakaway torque (N·m)                        22                                  14.1~28.2Carbon steel natural color bolt (GB/T18747.1-2002)Average dismounting torque (N·m)        30                                   16.9~33.9Carbon steel natural color bolt (GB/T18747.1-2002)Working temperature (℃)                                                              -50~150Chemical/solvent resistanceAged under conditions indicated and tested @ 22°CSolvent                                           Temperature (℃)                 % of initial strength100h   500h   1000h   5000hEngine oil                                             125                               90       80        75        75Leaded petrol                                        22                                95       90        90        90Brake fluid                                             22                               100     100     100       100Ethanol                                                  22                                90       90        75        75Acetone                                                 22                                85       85        80        80Water/glycol                                           87                              100      70        65         60(50%/50%)Directions for useClean-up:For best results, clean all surfaces (external and internal) with a Huitian 7755 cleaning solvent and allow to dry.Gluing:Apply glue evenly to the thread engagement area, with sufficient glue to fill the thread gap, and tighten in one pass as required by the specification. Curing speed slows down as the gap increases If the cure speed is too slow, spray all threads with Activator 7769 and allow to dry.Assembly:Shake the product thoroughly before use. To ensure that the system achieves maximum performance, the recommended curing time is 24 hours or more to ensure that the adhesive layer is fully cured.CautionsNot suitable for use on plastic parts, not suitable for use in pure oxygen and oxygen-rich systems, and not for sealing chlorine or other strong oxidizing substances.Store unused glue in a sealed container for next use. Contaminated glue should not be refilled into the original bottle as this may affect the performance of the remaining glue.This product contains acrylic and methacrylate substances which are irritating to the skin and eyes. Recommended for use in a ventilated area. In case of accidental contact with eyes and skin, rinse immediately with water.Keep away from children for storage.For safe handling information on this product, consult the Safety Data Sheet (SDS).Packing specificationOrder code: 726201, 50ml/tube, 10 pcs/carton, 80 pcs/box726203, 250ml/bottle, 10 pcs/cartonStorageOptimal Storage: 8 °C to 21 °C. Storage below 8 °C or greater than 28 °C can adversely affect product properties.Shelf life is 18 monthsWe can also make:1. Low strength & thixotropic thread locker2. Middle strength & thixotropic thread locker3. High strength & oil resistant thread locker4. High strength & chemical resistant thread locker5. High strength & thixotropic thread locker6. High strength & high viscosity thread locker7. High strength & middle viscosity thread locker8. High-strength & high-temperature resistant thread locker9. High strength & fast osmotic thread lockerPerformance of thread locker and sealant anaerobic adhesive/pre-coated thread locker and sealant anaerobic adhesiveProduct nameAppearanceViscositymPa·sGB/T2794Density g/cm³GB/U3354Maximum filling gapmmFailure momentN·mGB/T18747.1Average disassembly torqueN·mGB/T18747.1Initial curing time minFull curing time hWorking temperature ℃7242Blue800 -1,600Thixotropy**1.00.13125<2024-50-1507243Blue1,600 -1,900Thixotropy**1.080.132010<2024-50-1507262Red1,800 -2,400Thixotropy**1.10.132232<2024-50-1507263Red800-1,200*1.10.133025<4524-50-1807271Red450~550 *1.10.132529<2024-50-1507272Red4,000-10,000Thixotropy***1.110.32325<6024-50-2307277Red6,000- 9,000***1.120.253231<2024-50-1507204Red7,000-15,000Thixotropy****1.1N/A22N/A<572-50-1507204DRed9,000~15,000Thixotropy1.1N/A25N/A≤572-50~1507213Red, yellow, blue, orange, rose red, blue-green1,600~3,0001.05N/A20N/A≤572-50~1507215Rose red, yellow, blue-green1,600~3,0001.05N/A20N/A≤572-50~150Note: *Viscosity - measured at Brookfield RVF 20rpm: *2 # rotor **3 # rotor ***4 # rotor ****5 # rotorOur Advantages:1. Listed company in China (stock code: 300041)2. Famous Trademark of China3. Fast Delivery4. OEM services/small orders are welcome